My husband‘s work is finally allowing him to wear a smart watch. Long story.
For years he has wanted one so that he can track his health stuff but mainly, his sleep. The past three nights that he has had this watch, this is what he’s been getting:
My watch (series 8 45mm SS) gets this information:
(The last two days for me I had to input the information manually because I fell asleep before putting my watch back on from charging it 😩)
Is there something he needs to specifically do for the Ultra 2 to track his REM, deep, etc. sleep? He set up his stuff in the watch and health apps the same way I have.
Thanks in advance!
Hello, had this same issue on my ultra 1. I fixed it by deleting my sleep focus under setting and sleep schedule under the health app. Restarted both devices and set up the sleep focus and schedule again. Worked for me, your mileage may vary.
Make sure he’s enabled Track Sleep with Apple Watch: Watch App > Sleep
Is his watch on his wrist tight enough? I have the Ultra 2 and works fine for me
Sleep tracking is kinda buggy, apparently you need to set a fixed sleep schedule and it’s only tracking inside that scheduled. when I didn’t set one up but activated sleep mode manually it didn’t track my sleep. I’m super disappointed at how bad the setup is :/
I just set focus mode to sleep and it works.
Since launch it always works just setting my watch to sleep focus. Never had a schedule.
Switch to Autosleep. I’ve been using it for years and it works really well. It’s fully automatic, no sleep schedule or sleep focus required.
Put the watch in sleep focus/mode.
I’m a fan of the AutoSleep app.
I’ve used AutoSleep for years - works great.
You can tweak it to most accurately record the time you’re in bed and how much is awake, light sleep, moderate sleep, deep sleep. It will automatically record a nap if I happen to take one during the day.
I usually charge my watch in the morning while having coffee and showering. It is on my wrist at all other times.
The sleep feature used to drive me nuts - it was inconsistent.
I’ve found that it works better since I turned off ‘sleep schedule’ and started to manually turn on ‘sleep focus’ when I go to bed.
Yea, the Sleep Tracking on AW is … lets be nice and say severly lacking. Having to put it in a sleep schedule/focus is just dumb. I’m sure Apple Executives and their little schedules can sleep and wake at the same time every day, but the rest of the world doesn’t work that way.
I don’t wear any device to sleep, and I don’t need one to tell me if I slept well or not. If I cared about sleep tracking, I’d whip out my very old Fitbit from my junk drawer. Sleep Tracking is one area that they have always run circles around AW in.
I have the same bug. I’m using autosleep now
Mine will be hit or miss if it tracks. I only use sleep focus and don’t have a “schedule.” Most nights it tracks. But there is the occasional night I will go to bed as I usually do and then wake up the next morning and go to check my sleep and there’s nothing there.
It sounds like all the settings are correct, so I would suggest simply powering off the watch and turning it back on. Make sure it’s updated also and hopefully it will sort itself out.
The app AutoSleep is better than apples still
Get AutoSleep, the onboard app for sleep tracking is trash. Moving over from a Fitbit I saw just how bad some of the native Apple apps were.
I know this won’t help OP’s spouse’s issue, but it might help someone else in the future:
I have two watches, a new one I wear during the day and the older one it replaced and I only wear for sleep tracking. I hadn’t been getting the sleep tracking for the past week, just pics like the one she posted for him.
It turned out that the issue was that I had turned off the “Auto Switch” a week ago to force an update through, but had forgotten to turn it back off. As soon as I turned it back to Auto Switch, the watch connected and this week’s accumulated sleep data synced.
Auto switch?
If you have two or more Apple Watches, you can go into the Apple Watch app on your phone and tap the “All Watches” link at the very top of the screen. From there, it’ll show all of your watches with a checkmark next to the currently active one. At the top, there’s also a switch to turn on and off “Auto Switch” which lets you choose the active watch manually or let the OS pick for you. The only time I’ve found turning Auto Switch off and doing a manual select to be needed/useful is if I’m trying to force a watchOS update.
Again, I don’t think this is going to help your spouse’s use case.
