I wanted to share my experience with waxing my bike chains.

I was resistant to waxing my chains because it seems that a lot of people felt it was “too much work”.

But having to constantly clean black shit off my chains after every ride, then spend time degreasing and re-lubing, I figured I’d try waxing when I got my gravel bike.

Now, thousands of KM later and having converted all three bikes to waxed, there’s no way I’d go back. The time saved could be measured in hours per month.

First, the biggest complaint is chain prep. Yeah, regardless if you’re waxing or not, you’ll need to prep a new chain by removing the factory grease. With waxed, you do this once, and no more worrying about degreasing ever again. Make like easy and get Silca’s chain stripper, and it’s a 10 minute, one-step process.

Ongoing chain maintenance couldn’t be easier. After every ride, give the chain a quick wipe (or not). My chain stays clean, even after a 200 km ride.

And if you ride in wet or dirty conditions? Guess what, you’re in for a LOT of work if you lube your chain. With waxed, keep a second (or third) chain ready to go, and you just swap it out (10 seconds of effort). Take the dirty chain, give it a wipe if it’s only been wet, or pour boiled water onto it if you want to “reset” the chain to bare metal. Then drop it into the waxing pot for a re-wax. You don’t have to stand at the pot, so there’s no real time commitment here. I’ve spent more time completely dirtying large microfiber cloths trying to get my chain “clean” when lubed (hint: it’s never clean if you use a wet lube, not without solvents and an ultrasonic cleaner).

For actual immersion wax, I do it every 1000 km (sooner than you need to), and use a drip wax every 200 - 250 km to keep things fresh.

Honestly, wax is easier, cleaner, and takes less time to maintain vs wet lube.

The only downsides? The initial cost to get started. But this is offset by not having to replace chains or other components prematurely. You actually save money in the long-term when using waxed chains.

Some might argue that “you can’t run waxed chains in muddy or constantly rainy conditions”. Well, at the same time, your wet lube isn’t really helping matters in those situations, either. Waxed is still better, and you can swap chains much faster than you can clean the grinding paste from a wet lubed chain.

Who would I not recommend waxed chains to? Someone who rarely uses their bike. Drip lube will be “good enough” in those cases. But anyone else would benefit from waxing their chain.

  • Avid Amoeba@lemmy.ca
    link
    fedilink
    arrow-up
    34
    ·
    edit-2
    2 months ago

    You know what’s even easier? Forgetting to lube your chain for a while. Then avoid lubing it out of shame to face your failure. Then measuring the chain wear after a year to discover no significant degradation.*

    * Might require extra strong ebike-specific chains like KMC X11e EPT

    • lud@lemm.ee
      link
      fedilink
      arrow-up
      28
      ·
      2 months ago

      Even easier is not caring or even knowing that you are supposed to do anything.

      • Showroom7561@lemmy.caOP
        link
        fedilink
        arrow-up
        6
        ·
        edit-2
        2 months ago

        Ah, you must be one of those cyclists I can hear a mile away! SQUEAK, SQUEAK, SQUEAK!! 😂

        • Avid Amoeba@lemmy.ca
          link
          fedilink
          arrow-up
          12
          ·
          edit-2
          2 months ago

          Another surprising thing for me is that at no point did it start making shameful noises.

              • Showroom7561@lemmy.caOP
                link
                fedilink
                arrow-up
                2
                ·
                2 months ago

                Sounds like a dream! I’m sure at some point I’ll go with a belt drive. For now, I’m quite content with a low-maintenance chain drivetrain. Especially for their ubiquity, lower cost, and ease of repair while out in the middle of nowhere. LOL

                  • Showroom7561@lemmy.caOP
                    link
                    fedilink
                    arrow-up
                    3
                    ·
                    2 months ago

                    Changing a rear tyre on a split frame in the middle of no where would be beyond me.

                    I don’t think it’s that difficult, at least not from the videos I’ve seen. But it certainly would be a challenge if you weren’t in a comfortable area to do the work.

          • Showroom7561@lemmy.caOP
            link
            fedilink
            arrow-up
            3
            ·
            2 months ago

            One thing I’ve done with my winter bike is added a front fender extender (DIY), which prevents any spray from hitting the front chainrings, chain, or down tube. Last year, it was a total game changer. The only thing I couldn’t really help with was spray from the rear fender, which drips downwards onto the chain and cassette.

            I don’t even think a Dutch-style chain guard would help prevent contamination from the rear cassette getting drenched.

            But the best “winter bike” is one with an internal gear hub, and a belt drive. And an aluminum frame. Unless you really abuse the hell out of it, there should be very little to worry about.

        • lud@lemm.ee
          link
          fedilink
          arrow-up
          1
          ·
          2 months ago

          Haha, luckily I haven’t biked for quite a few years. My work is pretty away and I can play Ghost of Tsushima on the train.

    • Showroom7561@lemmy.caOP
      link
      fedilink
      arrow-up
      3
      ·
      2 months ago

      Then measuring the chain wear after a year to discover no significant degradation.

      How many miles/km?

      Yes, good chains last longer. But good waxed chains can outlive the life of some bikes (20,000km on a waxed chain is not unheard of). And it preserves the components at the same time.

      • Avid Amoeba@lemmy.ca
        link
        fedilink
        arrow-up
        1
        ·
        edit-2
        2 months ago

        Not too many, perhaps 2000km. Spring/summer/fall, no water or dirt riding. The cassette is SLX, derailleur and shifter are XT. I don’t ride a huge amount at the highest gears which suffer from higher wear due to the fewer teeth count. I recently lubed it with Silca Synerg-e and it’s bit quieter but the shifting performance was excellent before and after that. With all that said, I have no doubt I’ve worn it more than if I had properly maintained it. Perhaps significantly more. Nevertheless I was flabbergasted at the state of the drivetrain after this much mismaintenance. 😂

        • Showroom7561@lemmy.caOP
          link
          fedilink
          arrow-up
          2
          ·
          2 months ago

          Yeah, with 2000km, I wouldn’t expect much wear from a high-end chain like that. Before waxing, I was using Synergetic, which does help to preserve components. But it was still dirty, and I just got tired of always seeing black when I wiped the chain!

          Now, I can literally put a dropped chain back on my chainring, and don’t even have to wipe my hands. It’s wild how clean a chain can be after 1000km of low effort maintenance!